Storm Doors / Built to size

Manufactured Home Storm Doors

Manufactured-home storm doors often use different jamb depths, hinge systems, thresholds and nominal sizes than doors for site-built houses. A correct replacement must be matched to the actual opening and frame details rather than selected from a conventional storm-door chart.

Actual-frame sizing. The replacement is planned from measured mounting dimensions, jamb depth and threshold geometry.
Hinge identification. Existing hinge style and locations are documented instead of assumed from the home type.
Outswing clearance. Steps, rails, landings and adjacent walls are checked through the full door arc.
Wall-aware fastening. Anchors and sealant are selected for the specific frame and siding construction.

Build a quote request How to measure

The range

Compare manufactured home storm doors

1 planning configurations / final scope confirmed in writing

Storm Doors

Mobile Home Door

Mobile Home Door is a single-door option in our manufactured home range, with a broad glass area. Final size, swing, screen or glass arrangement, finish and hardware are confirmed from the opening before a quote is approved.

Shop Now

Related collections

Ranges that solve a similar opening, or the same opening a different way.

Screen-Only Doors Custom-Size Replacement Storm Doors Designer Security Doors Forged Iron Security Doors Patio Security Gates Security Door Locks and Hardware

Configure

How to choose manufactured home storm doors

The goal is a door that clears the exterior landing, seals against the existing frame and coordinates with the main entry without unnecessary field cutting. Photos of the current hinge and threshold are especially valuable.

Compare actual frame dimensions, outswing direction, hinge type, lower panel, glass and screen arrangement, latch height, closer mounting and the way the door meets the threshold. Model-year assumptions are less reliable than measurements.

Measure the frame where the replacement will mount, not just the old slab. Record three widths and heights, frame depth, hinge locations, threshold profile and any exterior trim or siding that limits fastening.

Fit starts with the mounting opening. Take three width and three height readings, both diagonals and clear photos. The measuring guide explains the complete photo and dimension set.

Build a quote request

Add the opening details you know. Final dimensions, operation and availability are reviewed before any order is approved.

Opening width (in)

Opening height (in)

Finish

Glass / screen preference

Quantity

Hinge side (viewed from outside)

Decision guide

What to settle before choosing a configuration

Actual-frame sizing

The replacement is planned from measured mounting dimensions, jamb depth and threshold geometry.

Hinge identification

Existing hinge style and locations are documented instead of assumed from the home type.

Outswing clearance

Steps, rails, landings and adjacent walls are checked through the full door arc.

Wall-aware fastening

Anchors and sealant are selected for the specific frame and siding construction.

Written dimensions

Finished size, hinge side and opening convention should be explicit before approval.

Complete scope

Glass, screen, hardware, frame and included components belong on the quote.

Buyer guide

Plan manufactured home storm doors around the entry

Where this door type works

The goal is a door that clears the exterior landing, seals against the existing frame and coordinates with the main entry without unnecessary field cutting. Photos of the current hinge and threshold are especially valuable.

What to compare before requesting a quote

Compare actual frame dimensions, outswing direction, hinge type, lower panel, glass and screen arrangement, latch height, closer mounting and the way the door meets the threshold. Model-year assumptions are less reliable than measurements.

Measurements and opening photos

Measure the frame where the replacement will mount, not just the old slab. Record three widths and heights, frame depth, hinge locations, threshold profile and any exterior trim or siding that limits fastening.

Installation planning

Use fasteners appropriate for the wall and frame construction, preserve required flashing and sealant paths and verify that the outswing does not conflict with stairs or a narrow landing. Do not crush thin framing by overtightening.

Care and service life

Inspect perimeter sealant, sweep contact and hinge screws regularly. Lightweight frames show misalignment quickly, so correct rubbing or incomplete latching before the fasteners loosen further.

A costly mistake to avoid

Do not force a residential storm door into a manufactured-home opening by trimming structure or moving the threshold without understanding the wall and water-management details.

What the written quote should identify

For manufactured home storm doors, the final scope should identify the finished opening or frame dimensions, measurement convention, hinge side, swing, frame and panel arrangement, glass or screen system, finish, hardware preparation, included accessories, delivery method and installation responsibility. If a choice affects fit, operation, appearance or later service, it belongs in the written document rather than an assumption made from the illustration.

How to compare two configurations fairly

Place the options side by side and normalize the components before comparing the total. One configuration may include a screen, closer, handle set, retainer, pairing hardware or specialty frame that another leaves out. Also compare the work expected at the opening: trim repair, subframe, anchors, sealant, removal, unloading and disposal can change the real project cost even when the door descriptions sound similar.

Configuration images are planning illustrations. The approved written quote defines the final dimensions, components, finish and hardware.

Questions

Manufactured Home Storm Doors FAQs

Are manufactured-home doors standard sizes?

Common nominal sizes exist, but actual openings, frames and hinge systems vary. Measure the specific mounting surface before ordering.

Can I use a regular storm door?

Sometimes a compatible configuration exists, but frame depth, hinges, threshold and fastening may differ. Compatibility should be verified, not assumed.

Which way should it swing?

Many exterior storm doors swing outward, but the landing, stairs, railings and local requirements must allow the full arc safely.

What photos should I send?

Full exterior and interior views plus close-ups of the top, sill, hinges, latch area, frame depth and surrounding siding.

Why does the threshold matter?

It affects sweep contact, water management and overall height. A mismatched bottom detail can leave a gap or prevent the door from closing.

Keep looking

Related door types

Screen-Only Doors

Screen-only doors are built for airflow and insect control rather than glass weather protection. Their performance depends on mesh selection, edge retention, frame rigidity and how well each door closes against the opening.

Custom-Size Replacement Storm Doors

Custom-size replacement storm doors should solve non-standard openings without unnecessary reframing. That requires more than copying an old slab: the exterior mounting surface, sill, square, hardware clearance and desired glass or screen operation all belong in the order.

Designer Security Doors

Designer security doors combine an ornamental exterior pattern with a rigid protective frame. Start with the opening and the daily use of the entry, then compare sightlines, mesh coverage, lock position and swing clearance instead of choosing on pattern alone.

Forged Iron Security Doors

Forged iron security doors make a stronger architectural statement than a light storm-door frame. The right design must fit the scale of the facade, preserve a practical path through the entry and coordinate with the glass, screen and hardware behind the ironwork.

Security Doors